Merge tag 'iio-fixes-for-6.6a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-linus

Jonathan writes:

1st set of IIO fixes for 6.6

Note last minute rebase to fix up a stale Fixes tag. All patches have been
in Linux-next for some time.

adi,ad3552r
 - Fix swapped device IDs for the two parts that are supported.
adi,ad7192
 - Use the right reference voltage source.
adi,ad7292
 - Fix additionalProperties to be false, not true.
adi,ad74413
 - Add missing Kconfig depends on IIO_BUFFER and IIO_TRIGGERED_BUFFER
adi,admv1013
 - Fix up some corner cases for the mixer vgate register value.
bosch,bmp280
 - Fix a null pointer dereference caused by a wrong boolean operator.
bosch,bno055
 - Add missing Kconfig depends on IIO_BUFFER and IIO_TRIGGERED_BUFFER
freescale,imx8eqxp
 - Fix some wrong register addresses.
google,cros_ec
 - Fix a use after free if very badly timed buffer disable occurs by
   holding the device in buffered mode.
infineon,dps310
 - Expand a timeout so we don't hit it on working parts.
meas,m5611
 - Allow for a ROM CRC of 0 as it is a valid value and there are devices
   out there where it happens.
murata,irsd200
 - Make sure the buffer used to build up the scan is large enough to take
   the timestamp.
rohm,bu27010 binding
 - Add a missing required vdd-supply
vishay,vcnl4000
 - Don't power down chip in wrong place.

* tag 'iio-fixes-for-6.6a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
  iio: pressure: ms5611: ms5611_prom_is_valid false negative bug
  dt-bindings: iio: adc: adi,ad7292: Fix additionalProperties on channel nodes
  iio: adc: ad7192: Correct reference voltage
  iio: light: vcnl4000: Don't power on/off chip in config
  iio: addac: Kconfig: update ad74413r selections
  iio: pressure: dps310: Adjust Timeout Settings
  iio: imu: bno055: Fix missing Kconfig dependencies
  iio: adc: imx8qxp: Fix address for command buffer registers
  iio: cros_ec: fix an use-after-free in cros_ec_sensors_push_data()
  iio: irsd200: fix -Warray-bounds bug in irsd200_trigger_handler
  dt-bindings: iio: rohm,bu27010: add missing vdd-supply to example
  iio: admv1013: add mixer_vgate corner cases
  iio: pressure: bmp280: Fix NULL pointer exception
  iio: dac: ad3552r: Correct device IDs

Author: gregkh

Documentation/devicetree/bindings/iio/adc/adi,ad7292.yaml

@@ -61,7 +61,7 @@ patternProperties:
     required:
       - reg
 
-    additionalProperties: true
+    additionalProperties: false
 
 allOf:
   - $ref: /schemas/spi/spi-peripheral-props.yaml#

Documentation/devicetree/bindings/iio/light/rohm,bu27010.yaml

@@ -45,5 +45,6 @@ examples:
       light-sensor@38 {
         compatible = "rohm,bu27010";
         reg = <0x38>;
+        vdd-supply = <&vdd>;
       };
     };

drivers/iio/adc/ad7192.c

@@ -177,6 +177,7 @@ struct ad7192_chip_info {
 struct ad7192_state {
 	const struct ad7192_chip_info	*chip_info;
 	struct regulator		*avdd;
+	struct regulator		*vref;
 	struct clk			*mclk;
 	u16				int_vref_mv;
 	u32				fclk;
@@ -1008,10 +1009,30 @@ static int ad7192_probe(struct spi_device *spi)
 	if (ret)
 		return dev_err_probe(&spi->dev, ret, "Failed to enable specified DVdd supply\n");
 
-	ret = regulator_get_voltage(st->avdd);
-	if (ret < 0) {
-		dev_err(&spi->dev, "Device tree error, reference voltage undefined\n");
-		return ret;
+	st->vref = devm_regulator_get_optional(&spi->dev, "vref");
+	if (IS_ERR(st->vref)) {
+		if (PTR_ERR(st->vref) != -ENODEV)
+			return PTR_ERR(st->vref);
+
+		ret = regulator_get_voltage(st->avdd);
+		if (ret < 0)
+			return dev_err_probe(&spi->dev, ret,
+					     "Device tree error, AVdd voltage undefined\n");
+	} else {
+		ret = regulator_enable(st->vref);
+		if (ret) {
+			dev_err(&spi->dev, "Failed to enable specified Vref supply\n");
+			return ret;
+		}
+
+		ret = devm_add_action_or_reset(&spi->dev, ad7192_reg_disable, st->vref);
+		if (ret)
+			return ret;
+
+		ret = regulator_get_voltage(st->vref);
+		if (ret < 0)
+			return dev_err_probe(&spi->dev, ret,
+					     "Device tree error, Vref voltage undefined\n");
 	}
 	st->int_vref_mv = ret / 1000;
 

drivers/iio/adc/imx8qxp-adc.c

@@ -38,8 +38,8 @@
 #define IMX8QXP_ADR_ADC_FCTRL		0x30
 #define IMX8QXP_ADR_ADC_SWTRIG		0x34
 #define IMX8QXP_ADR_ADC_TCTRL(tid)	(0xc0 + (tid) * 4)
-#define IMX8QXP_ADR_ADC_CMDH(cid)	(0x100 + (cid) * 8)
-#define IMX8QXP_ADR_ADC_CMDL(cid)	(0x104 + (cid) * 8)
+#define IMX8QXP_ADR_ADC_CMDL(cid)	(0x100 + (cid) * 8)
+#define IMX8QXP_ADR_ADC_CMDH(cid)	(0x104 + (cid) * 8)
 #define IMX8QXP_ADR_ADC_RESFIFO		0x300
 #define IMX8QXP_ADR_ADC_TST		0xffc
 

drivers/iio/addac/Kconfig

@@ -24,6 +24,8 @@ config AD74413R
 	depends on GPIOLIB && SPI
 	select REGMAP_SPI
 	select CRC8
+	select IIO_BUFFER
+	select IIO_TRIGGERED_BUFFER
 	help
 	  Say yes here to build support for Analog Devices AD74412R/AD74413R
 	  quad-channel software configurable input/output solution.

drivers/iio/common/cros_ec_sensors/cros_ec_sensors_core.c

@@ -190,8 +190,11 @@ int cros_ec_sensors_push_data(struct iio_dev *indio_dev,
 	/*
 	 * Ignore samples if the buffer is not set: it is needed if the ODR is
 	 * set but the buffer is not enabled yet.
+	 *
+	 * Note: iio_device_claim_buffer_mode() returns -EBUSY if the buffer
+	 * is not enabled.
 	 */
-	if (!iio_buffer_enabled(indio_dev))
+	if (iio_device_claim_buffer_mode(indio_dev) < 0)
 		return 0;
 
 	out = (s16 *)st->samples;
@@ -210,6 +213,7 @@ int cros_ec_sensors_push_data(struct iio_dev *indio_dev,
 	iio_push_to_buffers_with_timestamp(indio_dev, st->samples,
 					   timestamp + delta);
 
+	iio_device_release_buffer_mode(indio_dev);
 	return 0;
 }
 EXPORT_SYMBOL_GPL(cros_ec_sensors_push_data);

drivers/iio/dac/ad3552r.c

@@ -140,8 +140,8 @@ enum ad3552r_ch_vref_select {
 };
 
 enum ad3542r_id {
-	AD3542R_ID = 0x4008,
-	AD3552R_ID = 0x4009,
+	AD3542R_ID = 0x4009,
+	AD3552R_ID = 0x4008,
 };
 
 enum ad3552r_ch_output_range {

drivers/iio/frequency/admv1013.c

@@ -351,9 +351,9 @@ static int admv1013_update_mixer_vgate(struct admv1013_state *st)
 	if (vcm < 0)
 		return vcm;
 
-	if (vcm < 1800000)
+	if (vcm <= 1800000)
 		mixer_vgate = (2389 * vcm / 1000000 + 8100) / 100;
-	else if (vcm > 1800000 && vcm < 2600000)
+	else if (vcm > 1800000 && vcm <= 2600000)
 		mixer_vgate = (2375 * vcm / 1000000 + 125) / 100;
 	else
 		return -EINVAL;

drivers/iio/imu/bno055/Kconfig

@@ -2,6 +2,8 @@
 
 config BOSCH_BNO055
 	tristate
+	select IIO_BUFFER
+	select IIO_TRIGGERED_BUFFER
 
 config BOSCH_BNO055_SERIAL
 	tristate "Bosch BNO055 attached via UART"

drivers/iio/light/vcnl4000.c

@@ -1513,7 +1513,6 @@ static int vcnl4040_write_event_config(struct iio_dev *indio_dev,
 
 out:
 	mutex_unlock(&data->vcnl4000_lock);
-	data->chip_spec->set_power_state(data, data->ps_int || data->als_int);
 
 	return ret;
 }